1. Boot SystemRescueCD

select keymap 22 (jp)

Connect backupHDD

mkdir /mnt/target

mount /dev/sdc5 /mnt/target;            Note: Don’t mount (whole)sdc

ls /mnt/target;     will show content of the backupHDD.

FSArchiver seems not working for NTFS yet.  Not confident with the usage of Partimage.  Anyway done with backup.

1. Download  **.iso.

2. Burn CD.

2.1 Set blanc CD in the driev. (Important!)

2.2. To find the drive:

root@debian-yu:/home/kiyoshi# wodim devices
wodim: No write mode specified.
wodim: Assuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
Device was not specified. Trying to find an appropriate drive…
Detected CD-R drive: /dev/cdrw
Using /dev/cdrom of unknown capabilities
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   :
Vendor_info    : ‘TSSTcorp’
Identification : ‘CDDVDW TS-L633A ‘
Revision       : ‘TM00’
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
wodim: No such file or directory. Cannot open ‘devices’.
2.3. root@debian-yu:/home/kiyoshi/Softwares# ls
Acronis  systemrescuecd-x86-4.6.0.iso

wodim dev=/dev/cdrw systemrescuecd-x86-4.6.0.iso
wodim: No write mode specified.
wodim: Assuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   :
Vendor_info    : ‘TSSTcorp’
Identification : ‘CDDVDW TS-L633A ‘
Revision       : ‘TM00’
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Speed set to 4234 KB/s
Starting to write CD/DVD at speed  24.0 in real TAO mode for single session.
Last chance to quit, starting real write in    0 seconds. Operation starts.
Track 01: Total bytes read/written: 467294208/467294208 (228171 sectors).

There are two discs:

1.  Buffalo HD-HBU2 ユーティリティCD version 1.20

This will work.  When product number is asked, type in the number on the disc 2

It shows message to upgarde, but no web page exist anymore. But anyhow installed acronis will work in somewhat primitive way.

2. Buffalo HD-WIU2/R1 ユーティリティCD version 3.00

This won’t work.

1. Set network connection on console of the printer. The printer will be assigned an IP address by rooter. This address together with mac address can be found in the networking report printout of the printer.

2. Visit rooter (191.168.0.1). Set an new fixed IP (192.168.0.101) on the device with the mac address reported above (d0:bf:9c:a3:fc).

（詳細設定→DHCP固定割り当て設定）

3. Visit the printer ( address asigned at 1.) Set the new IP address (192.168.0.101) manually. Close the browser and revist the printer with new address to confirm the new address setting.

4. The printer IP address is currently 192.168.0.101. with mask 255.255.255.0.

On WindowsXP;

1. Download driver from Elecom.

2. Disable the Wlan driver of the existing wlan device and disconnect the device(PC card).

3. Run Setup.exe in driver package.

Error message “ファイルがみつかりません”　in the process, but ignore it.

4. Plug in the device:  successful!

LDFLAGS += `pkg-config –libs gtk+-2.0 gthread-2.0` -lm

adding -lm  to LDFLAGS  was effective.

To disable touchpad:

synclient TouchpadOff=1